★ ★ ★ ★ ★
Proudly backed by over 1000+ 5-Star Reviews
Trusted by Las Vegas homeowners.
call for free estimate
Open Sesame technician checking a broken garage door spring above a closed door with a car parked inside a Las Vegas garage

Las Vegas broken spring emergency guide

Garage Door Spring Broke and Your Car Is Stuck Inside? What to Do in Las Vegas

You heard a bang from the garage, or you pressed the button this morning and the door lifted a few inches, groaned and stopped. Now the car you need is sitting behind a door that won’t open. This is one of the most common garage door calls in Las Vegas, and the first ten minutes decide whether it stays a spring repair or turns into an injury, a bent door or a burned-out opener.

Direct answer

If your garage door spring broke and your car is stuck inside, leave the door where it is, unplug the opener and don’t pull the red release or try to lift the door. A door with a broken spring is dead weight. Call Open Sesame Garage Door Repair Las Vegas at (702) 888-0842, 24/7, for a 30-minute emergency response.

Once a trained technician has replaced the spring and balanced the door, it opens normally and the car backs out on the same visit. Until then, plan another way to get where you’re going. The only time the release cord comes into it is when the door is fully closed and a technician has talked you through it, and even then a door that feels heavy goes straight back down.

Below: the first five things to do, how to confirm it’s the spring and not the opener, what to do depending on where the door stopped, the truth about the emergency release, why nobody should wind a torsion spring at home, how to decide whether to call tonight or first thing in the morning, how to get through the day without the car, and what happens when the technician arrives.

What should you do first when the spring breaks and your car is inside?

Stop, then make the door safe before you think about the car. The door isn’t going anywhere, and neither is the car, so there is no prize for moving quickly. These five steps take a couple of minutes and cover almost every situation.

  1. Stop pressing the button. Don’t try the wall button again, a second remote, the keypad outside or the phone app. Every attempt asks the opener to lift a door it was never built to lift.
  2. Unplug the opener. The plug is usually in a ceiling outlet right next to the motor unit. If you can’t reach it safely, switch off the breaker for the garage. This stops someone else in the house from pressing a button while you’re standing near the door.
  3. Leave the red release cord alone for now. We explain below exactly when it is and isn’t safe. If the door is open or partly open, it is not.
  4. Keep people, pets and the car out from under the door. If the door stopped partway, nobody walks under it, and nobody sits in the car beneath it.
  5. Look, don’t touch. From the floor, look up at the bar above the door, or along the tracks on each side if your door has side springs. A clear gap in a coil is the answer you’re looking for. Take a photo if you can do it from a safe spot.

Then call. Tell whoever answers three things in the first sentence: the spring broke, the car is stuck inside, and where the door is right now (closed, partly open or fully open). That is enough for a dispatcher to judge how urgent it is and what to bring.

It can feel strange to do nothing to the door itself. People are used to fixing a stuck thing by pushing harder. A garage door is the exception, because the part that failed was storing the energy that made the door light. Once that energy is gone, pushing harder only moves the weight onto you, the opener or the cables.

Is anyone hurt or trapped? If a person is pinned, injured or stuck somewhere they can’t get out of, call 911 first. A garage door company is the second call, not the first.

How do you know it’s the spring and not the opener?

A broken spring and a dead opener can look the same from inside the car: you press the button and the door doesn’t open. The difference matters, because a dead opener with good springs is the one situation where you can usually get the car out yourself, and a broken spring is the one where you shouldn’t try.

Signs that point to a broken spring

  • A loud bang with nobody touching the door. A torsion spring that snaps under tension sounds like a firecracker or a dropped sheet of steel. Many people hear it in the evening or overnight and only find the problem the next morning. Our post on what a loud bang from the garage usually means walks through that moment in detail.
  • A gap in the coil. On a torsion system the spring sits on a steel shaft right above the door. A broken one usually shows a gap of a couple of inches where the coil has separated and unwound.
  • The door rises a few inches and stops, or the opener runs and strains while the door barely moves. Many openers have a force limit and give up when the load is far heavier than normal.
  • The top section bends where the opener arm attaches, because the opener is pulling on one point of a door that won’t lift.
  • Loose or slack lift cables hanging beside the door, or a cable that has come off its drum at the end of the shaft.
  • The door sits crooked, higher on one side than the other.

Signs that point to the opener or power

  • No sound and no light from the opener at all, which suggests power, a tripped GFCI outlet or a breaker.
  • The motor hums but the door doesn’t move and the springs look whole, which can mean a stripped drive gear or a problem with the trolley. Our guide to an opener that hums but won’t move the door covers that case.
  • The door starts down, then reverses, which is almost always the safety sensors or a limit setting rather than a spring.
What you notice More likely What to do
Bang earlier, visible gap in the spring Broken torsion spring Leave the door, unplug the opener, call
Door lifts a few inches then stops Broken or very weak spring Stop trying; don’t use the release
Cable hanging loose or door crooked Spring or cable failure Don’t move the door at all; call
Opener completely silent, springs look whole Power or opener Check the outlet and breaker first
Motor hums, springs look whole, door doesn’t move Opener drive problem Unplug; the release may be an option (see below)

When the signs are mixed, treat it as a spring problem. Guessing wrong in that direction costs you a few hours. Guessing wrong in the other direction can cost a lot more.

Where did the door stop? What to do if it’s closed, partly open or fully open

The position of the door matters more than anything else in the next hour. It tells you how much energy is still held up in the system and what happens if something else lets go.

1

Door fully closed

This is the safest position, and it’s the most common one when the spring breaks overnight. The door is resting on the floor, so nothing is holding its weight up. Leave it closed. Unplug the opener, keep the car parked and use another door to get in and out of the house. The garage stays secure, the car stays where it is, and the technician starts from a stable door.

2

Door partly open

This is the dangerous one. The door is being held in the air by whatever is left: the opener’s trolley, a remaining spring, the cables and friction in the tracks. If any of those let go, the door comes down. Don’t pull the release, don’t run the opener to finish closing it, and don’t try to push it up or pull it down by hand. Keep everyone out of the doorway and don’t sit in the car under it. Tell the dispatcher it’s stuck partway so the technician can plan how to support it before working on it. Our post on a garage door stuck halfway explains the other reasons a door stops mid-travel.

3

Door fully open

If the door is all the way up when the spring breaks, it is usually being held by the opener and the horizontal tracks. It might look like the easy case, because the car could simply back out. Whether that is safe depends on the door staying put, and you can’t judge that from the floor. Don’t pull the release cord: that disconnects the one thing holding the door up. If the technician says on the phone that it’s safe to back the car out without touching the door, do it slowly and in a straight line. If there is any doubt, leave the car where it is and wait.

If the door is crooked, a cable is hanging, or a roller has popped out of the track, add that to the list of things to say on the phone and don’t move the door in any direction. That combination is closer to an off-track emergency than a simple spring swap, and it needs to be secured before anything else happens.

Can you use the emergency release to get the car out?

Usually not, when the spring is broken. The red handle hanging from the opener rail is designed for one main job: letting you move a balanced door by hand when the opener can’t, for example in a power outage. It disconnects the door from the opener’s trolley. After that, the springs are supposed to carry the weight while you guide the door. With a broken spring, nothing carries the weight.

What the rules and the manuals say

The federal safety standard for residential garage door openers, 16 CFR Part 1211, sets out how the release has to work. The handle must be red, adjustable to six feet above the floor, and able to detach the opener with no more than 50 pounds of hand force with the door obstructed in the down position. In other words, it was specified around a closed door. The same standard requires opener instructions to carry this warning: if possible, use the emergency release only when the door is closed, and use caution with the door open, because weak or broken springs may allow the door to fall rapidly, causing injury or death.

DASMA, the trade association for door and opener manufacturers, says the same in plain terms in its home checklist (TDS 167): if a spring is broken, do not operate the door until the spring is replaced. Its power-outage guidance (TDS 385) describes pulling the release and lifting the door by hand, and it adds a condition that gets left out of a lot of online advice. DASMA says it is “particularly important to be able to manually open and close the door with little effort.” A broken-spring door fails that test by definition.

When the release might come into it

  • The springs on the shaft or tracks are visibly whole, and the problem is the opener or power. Then the release is the normal way out: pull it with the door fully closed, lift from the handle or bottom section, and the door should rise smoothly and stay put around halfway.
  • The door is fully closed, a technician has asked you specific questions on the phone and told you it’s appropriate to try. Even then, if the door feels heavy, stop and lower it right away.

When it doesn’t

  • The door is partly or fully open.
  • You can see a gap in a spring, or the door lifted only a few inches before the opener quit.
  • A cable is loose, the door is crooked or a roller is out of the track.
  • You’d need two or three people to hold the door up while someone else drives.

That last one comes up a lot. Some websites suggest getting a couple of strong neighbors to lift the door and prop it while you back out. A double door without its springs can be far heavier than it looks, the weight shifts as the sections roll into the curve of the track, and nobody can hold it steady and also get out of the way if a hand slips. We’d rather you missed a morning than tried it.

If you already pulled the release on an open door: step back, keep everyone clear of the opening and don’t try to catch or re-hook the door. Call and describe exactly where it stopped.

Why can’t the opener lift the door, and why should you stop pressing the button?

The opener only moves the door. The springs lift it. On a correctly balanced door, the springs carry nearly all of the weight, which is why a working door can be lifted by hand with a light push and stays roughly where you leave it. The opener’s motor and drive are sized for that easy job: pull a balanced door along its tracks, and stop and reverse if it meets resistance.

DASMA puts it simply in its opener guidance: openers are designed to open doors that are properly balanced. When a spring breaks, the door’s full weight lands on the opener’s trolley, the arm attached to the top section, and the drive gear or belt. Three things tend to happen if people keep trying:

  • The top section bends. The opener arm pulls on one bracket near the top of the door. With nothing lifting from the sides, the section folds at that point. A spring repair can turn into a section replacement.
  • The opener strips or burns out. Many openers use a plastic drive gear that wears or strips under a load far heavier than normal, and a dead-weight door is exactly that load.
  • Cables come off the drums. As the door jerks up and stops, slack builds in the lift cables. When the door drops back, a slack cable can jump off its drum at the end of the shaft, and now the door can hang crooked.

There’s also the person-in-the-house problem. If the opener is still plugged in, anyone with a remote in their car, a keypad code or an app on their phone can try to open the door while you’re standing under it looking at the spring. Unplugging takes that off the table.

Some newer openers are designed to stop on their own when they sense a load like this and may show an error light. That’s the opener protecting itself. It isn’t a sign that one more try might work.

If you want to understand the whole lifting system and why the spring and opener have separate jobs, our post can you open a garage door with a broken spring? goes deeper into the mechanics. This guide stays focused on the trapped car.

Why you should never try to wind or replace a torsion spring yourself

A spring repair looks simple in a video. There’s a bar, a spring, some bolts and a couple of steel rods. The part the video can’t show is how much energy a wound torsion spring holds and how quickly it releases it.

A torsion spring is wound by turning a cone at its end, a quarter turn at a time, with winding bars pushed into holes in the cone. On a typical door the spring is wound many full turns to balance the door’s weight. Every one of those turns is stored energy. If a bar slips out, or someone uses a screwdriver or the wrong size rod, the cone spins back with enough force to break a wrist, a jaw or a cheekbone. Set screws that are loosened at the wrong time release the whole spring at once.

DASMA’s checklist is direct about it: don’t try to remove, repair or adjust springs or anything that door spring parts are fastened to, such as wood blocks, steel brackets or cables. Because of the dangers, all repairs and adjustments must be done by a trained door systems technician using proper tools and instructions. Opener and door manuals repeat the same warning on their labels, and there’s a spring warning tag on most spring brackets for the same reason.

There’s a practical side too. A replacement spring has to match the door. The wire size, inside diameter and length are chosen for the door’s weight and height, and the number of turns is set for that door. A spring that’s a little off leaves the door heavy or makes it fly up. Either way the opener ends up doing work it shouldn’t, and the new spring wears out early.

What about the other spring on a two-spring door?

Many double doors have two torsion springs on one shaft. When one breaks, the other has usually been through the same number of cycles. A technician will tell you what they find and why, and the decision is yours. The point for tonight is simpler: even with one spring left, the door is not safe to operate, and the remaining spring is still under tension. Leave both alone.

Things people try that make it worse

  • Clamping vise grips on the shaft to “hold” the spring while loosening bolts
  • Loosening the set screws on the winding cone of the broken or the good spring
  • Cutting or unhooking the lift cables to free the door
  • Removing the bottom brackets, which on most doors are under cable tension

Every one of those turns a closed, stable door into something that can move without warning. If you’ve already started, stop where you are, step away from the door and tell the technician exactly what was loosened.

Torsion or extension springs: what changes when the car is trapped?

Most modern sectional doors use torsion springs on a shaft above the door. Some older homes and some single-car doors still use extension springs, which run along the horizontal tracks near the ceiling on each side and stretch as the door closes.

Torsion spring systems

The spring is wrapped around a shaft, so the shaft contains the broken pieces. When it breaks you’ll see the gap, and the shaft may be a little loose in its bearings. The door usually stays closed if it broke while closed. This is the setup where “leave it shut and call” is easiest to follow.

Extension spring systems

Extension springs are stretched furthest when the door is closed, which means they hold the most energy then. A broken extension spring can whip across the garage if there isn’t a containment cable running through its center. DASMA’s checklist asks homeowners to check for exactly that: extension springs should be contained by a secure cable through the middle of each spring. If yours don’t have one, stay well back from the tracks, keep the car where it is and don’t try to open the door at all. Tell the technician on the phone that you have side springs with no safety cables, because it changes how they’ll approach the door.

With extension springs, one side often breaks and the other doesn’t. That’s why these doors tend to go crooked when they fail: one side is still being pulled up and the other is not. A crooked door is one more reason to leave it alone.

Not sure which you have?

Look up. A thick coil on a bar right above the top of the door is a torsion spring. Long springs running parallel to the ceiling tracks, usually with pulleys and cables at the end, are extension springs. Some lightweight one-piece doors and some imported or custom doors use other systems; if yours doesn’t look like either, take a photo and describe it on the call.

For background on why springs give out in this climate and how long they tend to last, see how long garage door springs last in Las Vegas heat.

What shouldn’t you do to get the car out?

When someone has a shift at six or a flight at eight, ideas start to sound reasonable that wouldn’t at any other time. These are the ones we hear most often, and why each one goes wrong.

1

Propping the door with a 2×4, a ladder or a car jack

A prop holds one point of a door that wants to come down across its whole width. Sections flex, the prop shifts on a smooth garage floor, and anyone driving out passes right under the door. Jacks are worse, because they push up on a single section and can bend it or pop rollers out of the track.

2

Lifting it with neighbors and driving out underneath

Covered above, but it’s the most common one. People can lift a lot for a second. Holding a heavy door steady overhead, evenly on both sides, while a car backs out is a different thing. If one person’s grip goes, the rest of the weight goes to whoever is left, or onto the car.

3

Backing the car into the door or pushing it from outside

A closed door is not a barrier you can nudge open. Bumping it bends sections, pulls tracks off the wall and can knock the door off its tracks. Now you have a damaged door, possibly damage to the car, and a much longer repair. If the door has already been hit, our post on a garage door hit by a car covers what happens next.

4

Running the opener “one more time”

Each try strains the opener, puts more slack in the cables and stresses the top section. If the first two tries didn’t work, the third won’t either.

5

Cutting cables or removing hardware

Cables, bottom brackets and spring hardware are often still under tension even with a broken spring. Cutting or unbolting them releases that tension in a direction nobody planned for. Our guide on what to do when a garage door cable snaps explains why cables are treated like springs.

6

Ordering a spring online and fitting it before work

Besides the injury risk, a spring has to be matched to the door’s weight and size. A wrong spring leaves you with a door that still doesn’t balance, and you’ll often still be waiting on a technician, just later.

Doing nothing to the door is a decision, and it’s usually the right one. A closed garage door with a broken spring is stable. It only becomes dangerous when someone tries to move it.

Is a trapped car an emergency? Calling tonight versus first thing in the morning

A trapped car is inconvenient. Whether it’s an emergency depends on what that car needs to do and what else is going on with the door. We answer around the clock, so you can always call and talk it through. These questions help you decide how fast you need someone there.

Call now, any hour, if

  • The door is stuck partly or fully open and the house can’t be secured overnight.
  • The door is crooked, a cable is loose or a roller is out of the track.
  • Someone needs the car for medical reasons: dialysis, a hospital appointment, picking up medication, or a caregiver who has to reach a relative.
  • It’s the only vehicle in the household and someone has to get to an early shift, a flight or a court date, and there’s no realistic ride.
  • Anything is in the garage that can’t wait: a pet, refrigerated medicine, a delivery you’re responsible for.
  • The garage is your only practical way in or out of the house.

It can usually wait for a morning visit if

  • The door is closed, level and still, and the opener is unplugged.
  • You have another car, a ride, or nowhere you need to be until later.
  • The house is secure and the door from the garage into the house locks.

We wrote a longer guide on what counts as a garage door emergency in Las Vegas that covers stuck-open doors, impacts and opener failures as well as springs.

Whatever you decide, the safety steps don’t change. A morning appointment with an unplugged opener and a closed door is better than a rushed attempt to get the car out at midnight. If you want someone there tonight, Open Sesame’s emergency garage door repair in Las Vegas runs 24 hours a day with a 30-minute emergency response, and our 24-hour repair service page explains how after-hours calls work.

How do you get through the day without your car in Las Vegas?

The fix for the door and the fix for your morning are separate problems. Sorting out the second one takes the pressure off the first, and that pressure is what leads people to try lifting the door.

Line up a ride before you need it

Rideshare and taxis cover the whole valley, from Summerlin and Centennial Hills to Henderson and the east side. If you have an early start, book or check availability the night before. A neighbor, a coworker on the same shift or a family member may be easier than you expect, especially if you explain the car is locked in.

Use the other car, if there is one

In a two-car garage with a single wide door, both cars are usually stuck. In a garage with two separate doors, the other car may be fine, as long as its door works and nobody walks under the broken one to reach it. If a car is parked in the driveway, use that one and leave the garage alone.

Tell work and anyone waiting on you

A short message along the lines of “my garage door spring broke with the car inside, a technician is coming” is something most employers have heard before. Ask whether you can start later or work from home for the morning.

Things people forget are in the car

Wallets, work badges, laptop bags, car seats and medication often live in the car. You can usually reach those without opening the garage door at all, through the door from the house into the garage. Walk along the side of the car away from the door and the tracks, and don’t stand in the door’s path. If your car keys or house keys are in the car, see the lockout section below.

Plan for the visit

Someone needs to be home to let the technician into the garage, usually through the house. If that’s hard, say so on the call. Clear a path to the door inside the garage if you can do it without going near the tracks or under a raised door.

Once you know how you’re getting to work, the door can wait for a safe repair.

Heat, exhaust and a closed garage: Las Vegas safety while you wait

Las Vegas adds two risks that people in milder places don’t think about much.

Don’t run the car in a closed garage

It’s tempting to sit in the car with the engine on to stay cool or warm, charge a phone or wait for the technician. In a closed garage that’s how carbon monoxide builds up. The EPA describes carbon monoxide as odorless and colorless, lists exhaust from attached garages as a source of it in homes, and says plainly not to idle the car inside the garage. Turn the engine off and wait inside the house. If the garage connects to the house, keep the door between them closed. A working CO alarm in the house is worth having for this reason alone.

Summer heat in the garage

In the hot months a closed garage on a sun-facing lot gets much hotter than the house. That matters if anything heat-sensitive is in the car or the garage: medication, a pet, groceries, a phone or laptop left in the car. Get those out through the house door if you can do it without going near the door or tracks, and don’t let anyone wait in the garage. If a pet or a person is shut in a hot garage with no safe way out, that’s a reason to call 911 as well as a garage door company.

Cold mornings in winter

From late fall into winter, Las Vegas mornings can be near freezing even when the afternoons are mild. The National Weather Service office in Las Vegas posts the local forecast if you want to check. Cold doesn’t usually cause a spring to fail by itself, but it’s often the morning when an already worn spring finally lets go, because that’s when the door gets its first cycle of the day. The steps are the same: stop, unplug, leave the door, call.

Keep kids and pets away from the door

A garage with a broken door and a parked car is an interesting place for a child. Keep the house door to the garage locked until the repair is done. DASMA’s safety guidance is clear that people should stay out of the path of a door, and a broken door is less predictable than a working one.

What should you tell Open Sesame when you call?

A good first call saves time on the visit, because the technician can bring the right parts and plan how to handle the door before they arrive. You don’t need technical words. Describe what you see.

  • That a car is stuck inside, and when you need it.
  • Where the door is: fully closed, partly open (roughly how high) or fully open.
  • What you heard or saw: a bang, the door rising a few inches, the opener straining, a gap in a spring.
  • Which springs you have: one or two coils on a bar above the door, or long springs along the ceiling tracks.
  • Anything else that’s wrong: a loose or hanging cable, the door sitting crooked, a roller out of the track, a bent top section.
  • The size of the door: single or double, and roughly how tall. A photo of the door from inside helps.
  • The opener: whether it’s unplugged, and the brand if you can see it on the motor cover.
  • Anything you tried: pulling the release, lifting the door, loosening a bolt. Be honest. It changes how the technician approaches the door, and nobody will judge you for it.
  • Access: gate codes, HOA guard gates, where to park and the best number to text.

If you can safely take a photo of the broken spring from the floor, a clear shot of the gap and the end of the spring helps the technician confirm what’s broken before they arrive.

Open Sesame Garage Door Repair Las Vegas is at 7865 Bluewater Dr, Las Vegas, NV 89128, and answers (702) 888-0842 24 hours a day, 7 days a week. You can also send details through the contact page if it isn’t urgent, but for a trapped car, calling is faster.

What happens when the technician arrives?

The order of work matters more than the speed. On a broken-spring call with a car inside, a trained technician will normally work through roughly these stages.

1

Make the door safe before anything moves

The technician checks where the door is, whether the cables are still on their drums and whether the door is level. A door that’s partly open gets supported and secured in the tracks first. A closed door stays closed while they work above it.

2

Identify the spring and the door

They measure the broken spring and look at the door’s size and construction, because the replacement is chosen for that door’s weight. On a two-spring door they’ll also look at the spring that didn’t break and explain what they see.

3

Replace the spring with proper tools

The old spring comes off, the new one goes on and is wound with proper winding bars, a set number of turns for that door. This is the part that should never be done at home.

4

Check cables, drums, bearings and rollers

A spring failure puts a jolt through the whole system. Cables can fray, drums can shift and rollers can be knocked loose. The technician looks at those while the door is still disconnected from the opener.

5

Balance the door by hand

With the opener still disconnected, the door is lifted by hand. A balanced door moves smoothly and stays roughly where it’s left partway up. If it drifts up or drops, the tension is adjusted.

6

Reconnect and test the opener

The opener is reconnected and run through a full cycle. The safety reversal and the photo-eye sensors are tested, because those can be knocked out of line during a failure. Then the door goes up the normal way, and you back the car out.

You should be told what’s wrong and what the repair involves before work starts. Ask questions. A good technician will show you the broken spring and explain why any other part needs attention. Our guide on how long garage door repair takes in Las Vegas covers what affects the length of a visit, and our garage door spring repair in Las Vegas page covers the service itself.

Two doors, tandem garages and other ways out

Not every Las Vegas garage is a simple two-car box with one door. The layout changes what’s possible while you wait.

Two single doors side by side

Each door has its own springs and usually its own opener. If only one spring broke, the other door may work normally. Before using it, unplug the opener for the broken door so nobody presses the wrong button, and make sure you won’t walk or drive near the broken door’s path. If you’re not sure which opener controls which door, unplug both and use the working door by its wall button only after plugging that one back in.

Tandem or three-car garages

Some homes have a deep tandem bay or a third single door. A car parked behind another one in a tandem bay is only as free as the door in front of it. A car in a separate bay with its own door may be fine. The same rule applies: only use a door whose springs you can see are whole.

Golf-cart and side doors

Some homes in Summerlin and other master-planned neighborhoods have a narrow side door for a golf cart or bikes. That’s useful for getting things in and out, but it won’t help a car. Keep using it to get to the side yard or the street, not to work around the main door.

RV or oversized doors

Tall RV bays and oversized doors use bigger springs and heavier doors. Everything in this guide applies with more force. Don’t try to move one by hand.

When the car is half in, half out

If the door came down onto the car or stopped just above it, don’t drive. Leave the car exactly where it is, keep people away and call. The technician needs to support the door before the car is moved.

If the garage is your only way in, or your keys are in the car

Plenty of people in Las Vegas use the garage as their front door. The keypad outside opens the garage, and the house door inside is the one that gets used every day. A broken spring can leave someone outside the house with no key.

Locked out of the house

Try every other door and anyone who has a spare key: a family member, a neighbor, a property manager or an HOA office that keeps keys. A locksmith is the right call for the house door. Forcing the garage door open from outside is not an option with a broken spring, because you’d be lifting the full weight of the door with no control.

Tell us if the garage is your only way in. It moves the call up the list, and the technician will know someone may be waiting outside.

Keys, phone or wallet in the car

If you can get into the house, you can usually reach the car through the house door into the garage without touching the garage door. Walk on the side away from the tracks, don’t lean on the door, and don’t stand under it if it’s partly open. If the car is locked with the keys inside, that’s a car lockout and a separate problem from the door.

Keypads, apps and smart openers

Smart opener apps and keypads keep working until the opener is unplugged. That’s why unplugging is step two. If you have a smart opener, you can also disable remote access in the app until the door is fixed, so nobody opens it from work by habit.

Securing the house

If the door is stuck open, move valuables into the house, lock the door from the garage into the house and tell us when you call. Our post on a garage door stuck open covers that situation in more detail.

How do you avoid the next trapped-car morning?

Springs wear out. Each one is made for a certain number of open-and-close cycles, and a busy household that uses the garage as its front door can go through those cycles faster than expected. You can’t make a spring last forever, but you can usually catch a tired one before it strands a car.

Watch for early signs

  • The door seems heavier than it used to when lifted by hand, or the opener sounds like it’s working harder.
  • The door doesn’t stay put halfway when it’s disconnected from the opener.
  • One side of the door rises a little before the other.
  • You can see stretched-out gaps or rust along a spring’s coils.
  • Cables look frayed near the bottom brackets.

Do the monthly balance check, safely

DASMA’s checklist suggests that homeowners check door balance as part of routine care. With the door fully closed and the springs visibly whole, pull the release, lift the door by hand to about halfway and let go. A balanced door stays roughly in place. If it drops, rises quickly or feels heavy, close it again, reconnect the opener and have the springs looked at. Don’t do this check if you already suspect a spring problem.

Test the safety reversal

The same checklist covers the photo-eye test and the contact reversal test, in which the door should reverse when it touches a 2×4 laid flat in its path. These don’t tell you about the springs, but they’re part of the same visit and they matter for anyone walking under the door.

Book a tune-up when the door starts to feel different

An Open Sesame tune-up is $89. A professional tune-up includes a look at springs, cables, rollers, hinges and the opener. If a spring is near the end of its life, that’s the time to replace it, at a time that suits you, instead of at six in the morning with the car locked in. Our post on how often to get a garage door tune-up in Las Vegas explains what to look for.

Think about parking

If you have a driveway and an early commitment, and your door has been showing signs, parking outside the night before is a simple way to protect the morning.

Broken spring help across the Las Vegas valley

Open Sesame Garage Door Repair Las Vegas is based at 7865 Bluewater Dr, Las Vegas, NV 89128, near Desert Shores, and works across the valley. That includes Summerlin and Summerlin South, Centennial Hills, The Lakes, Spring Valley, Enterprise, Paradise, Sunrise Manor, Henderson and North Las Vegas. Our main Las Vegas garage door repair page lists the full range of work.

What you can count on when you call about a broken spring with a car inside:

  • The phone is answered 24 hours a day, 7 days a week, including nights and weekends.
  • A 30-minute emergency response for urgent calls, and same-day service.
  • A Nevada licensed contractor, NSCB #0083315. You can look up any contractor’s licence on the Nevada State Contractors Board website before work starts.
  • Springs, openers, cables, tracks and off-track doors are all part of the same service, so one visit can deal with whatever the spring failure knocked loose.

Open Sesame’s posted prices for the jobs in this guide: spring repair $189 to $550, off-track repair $125 to $275, and a tune-up is $89. Other work is quoted once the technician has seen the door.

Before any technician works on your door, ask what’s broken, what the repair involves and what it will cost, and get the answer before work starts. That applies to us and to anyone else you call. It’s the simplest way to avoid surprises on a stressful morning.

Frequently Asked Questions: Broken Spring, Car Stuck Inside

My garage door spring broke and my car is stuck inside. What should I do first?

Stop pressing the opener, unplug it, and leave the door where it is. Don’t pull the red release or try to lift the door, because without the spring the door is dead weight. Keep everyone out from under it and call a garage door technician. In Las Vegas, Open Sesame answers (702) 888-0842 24/7.

Can I pull the emergency release to get my car out with a broken spring?

Usually not. The release disconnects the door from the opener, and with a broken spring nothing else holds the door’s weight. Opener manuals warn that weak or broken springs can let the door fall rapidly. Never pull it with the door open. With the door closed, try it only if a technician advises it, and stop if the door feels heavy.

Can two people lift a garage door with a broken spring so I can drive out?

We don’t recommend it. A double door without its spring is much heavier than it looks, and the weight shifts as the sections roll into the curved track. Holding it level overhead while a car backs out leaves people under the door with no safe way to let go. Arrange another ride and wait for the repair.

Is a car stuck in the garage an emergency?

It depends on the car’s job and the door’s condition. A closed, level door with the opener unplugged can usually wait for a morning visit. Call right away if the door is stuck open or crooked, a cable is loose, someone needs the car for medical reasons or an early commitment, or the garage is the only way into the house.

Why won’t my garage door opener lift the door after the spring broke?

The springs do the lifting and the opener only moves a balanced door. When a spring breaks, the full weight lands on the opener’s arm and drive, so it strains, stops or reverses. Repeated tries can bend the top section, strip the drive gear or throw the cables off their drums, so unplug it and leave it.

Can I replace or wind a torsion spring myself?

No. A wound torsion spring stores enough energy to cause serious injury if a winding bar slips or a set screw is loosened at the wrong time. DASMA says all spring repairs and adjustments must be done by a trained door systems technician using proper tools. The spring also has to be matched to the door’s weight and size.

What if the door is stuck partly open with the car underneath?

Don’t drive the car, don’t pull the release and don’t run the opener. Keep everyone out of the doorway and away from the car. The door is being held by whatever is left of the system and could come down. Tell the dispatcher it’s stuck partway so the technician can support it before any work starts.

How do I know if it’s the spring or the opener?

Look up from the floor. A gap in the coil on the bar above the door, a loud bang earlier, or a door that rises a few inches and stops point to the spring. A completely silent opener with whole springs points to power or the opener. When the signs are mixed, treat it as a spring problem and leave the door alone.

Is it safe to sit in my car in the garage while I wait?

Not with the engine running. Idling a car in a closed garage can build up carbon monoxide, which you can’t smell. Turn the engine off and wait in the house with the door between the house and garage closed. In summer, take any medication, pets or electronics out of the hot car if you can do it without going near the door.

How long will my car be stuck after the spring breaks?

It stays inside until the spring is replaced and the door is balanced, which is normally done in one visit. How soon that happens depends on when you call and how urgent the situation is. Open Sesame answers 24/7 with a 30-minute emergency response in Las Vegas, so call (702) 888-0842 and describe the door’s position.

What should I tell the technician when I call about a broken spring?

Say a car is trapped and when you need it, where the door stopped, what you heard or saw, whether you have springs above the door or along the tracks, and anything else that looks wrong, like a hanging cable or a crooked door. Mention anything you already tried. A photo of the broken spring helps.

Can a broken spring damage my car?

A closed door with a broken spring usually sits still and won’t touch the car. Damage tends to happen when someone runs the opener, props the door, lifts it by hand or tries to drive out under it, and the door drops. If the door stopped above or onto the car, don’t move the car until the door has been secured.

Sources

Find Open Sesame Garage Door Repair Las Vegas

View on Google Maps · 7865 Bluewater Dr, Las Vegas, NV 89128

Spring Broke and Your Car Is Stuck in Las Vegas? Call Open Sesame

Leave the door where it is, unplug the opener and call (702) 888-0842. Open Sesame Garage Door Repair Las Vegas answers 24 hours a day, 7 days a week, with a 30-minute emergency response and same-day service across the valley. Nevada contractor licence NSCB #0083315.

7865 Bluewater Dr, Las Vegas, NV 89128 · Open 24/7 · Licence #0083315